Thursday, January 21st, 2010
I want to hang a baby blanket on the wall in my toddlers room to pad it because he likes to sit on a pillow in the corner and read. Not only will this look cute but it will be softer for him to lean aginst in case he hits his head. How can I do this without damaging the blanket and in a baby safe way. That means there can be nothing he could pull off and choke on. Thanks for the help!
A cheap way would be to use the clamp style pants hangers and then hang the hook ends through loops attached to the walls.
http://images.google.com.au/images?sourceid=navclient&rlz=1T4ADBF_enAU281AU284&q=pants%20hangers%20clamp&um=1&ie=UTF-8&sa=N&hl=en&tab=wi
Or you could use a quilt hanger. I don’t think the wire ones would be strong enough but there a number of other types that might be suitable.
http://images.google.com.au/images?sourceid=navclient&rlz=1T4ADBF_enAU281AU284&q=quilt%20hangers&um=1&ie=UTF-8&sa=N&hl=en&tab=wi
Technorati Tags: Aginst, Amp, baby blanket, Clamp, Google, Hangers, Hl En, Hook, Images, Quilt Hanger, Rlz, Safe Way, Sit, Toddlers, Utf 8
Posted in baby blanket | 7 Comments »
Wednesday, October 14th, 2009
When it comes to installing a new dishwasher, you need not to hire a plumber for this. It is very easy and you can do it yourself. You just have to follow the following steps.
However, before you start, make sure the following tools are available to you, as you will need them in the process.
Tools
Screwdriver
Multimeter
Slip-joint pliers
Needle-nose pliers
Adjustable wrench
Note: If you are replacing an old dishwasher, you must buy a same size new dishwasher.
Installation Process
The following steps will let you know how you can install a new dishwasher. We have assumed that you are replacing an old dishwasher with a new one. Therefore, the procedure starts from removing the old dishwasher first and then installing the new one.
1. Turn off the water supply at the valve.
2. At the electrical service panel, switch off the power for the dishwasher.
3. At the top of the dishwasher counter flange, you will find some screws. Unscrew them with the screwdriver to remove them.
4. Now pull out the bottom cover.
5. Be very careful. Make sure that you have turned off the power. Open the electrical box to confirm the same. You can do it by attaching the black multimeter contact to the ground and then touching the red contact to the white wire and the black wire.
6. At the end of the wires, attach wire nuts. Now remove the wires from the terminal screws and tuck them out of the way.
7. Find out where is the water supply under the washer.
8. Disconnect the water supply line from the water inlet by removing the nut.
9. Loosen the clamp and remove the hose to disconnect the drain hose from beneath the sink.
10. After disconnecting all the attachments, place a blanket in front of the dishwasher, slowly lift up the dishwasher and put it onto the blanket.
11. Keep a towel ready with you because in this process of lifting up the dishwasher and putting it onto the blanket, some water may spill out. If it happens, just wipe it with the towel.
12. Now that you have removed the old dishwasher, clean the area where the old dishwasher was placed and where you have to install the new one.
13. Position the new dishwasher on its back.
14. Connect the drain hose with a compression clamp.
15. Wrap the water line connection with Teflon tape and attach the 90-degree brass fitting that is used to connect the water line, also known as dishwasher 90.
16. Adjust the front legs of the new dishwasher downward so that you can easily slide the unit into place. Meanwhile, with the help of an assistant, slide the drain hose also under the sink.
17. Connect the water line underneath the dishwasher to the dishwasher 90.
18. Pass the electric cable through the sleeve on the dishwasher and tighten the same so that the cable could not be pulled out.
19. Now make all the connections of the wire: ground wire to the green screw, white wire to white wire, and black wire to black wire. Use wire nuts to secure the connection.
20. Connect the new drain hose at its previous position.
21. Fill the water line by opening the hot water valve.
22. Carefully examine if there is any leaks.
23. If any leaks occur, recheck all the connections and test again.
24. Once you are sure that there is no leaks or problem as such, go ahead.
25. Adjust front legs of the dishwasher and position it properly on a level.
26. Drive the small mounting screws into the underside of the countertop through the flange in order to attach the dishwasher to the countertop.
27. Reconnect the water supply line.
28. Turn on the power and your dishwasher is ready to act.
Hence, if you follow the above steps, you can easily install your new dishwasher yourself. However, you need to be very careful especially while making the electric connections. Make sure that you have turned off the electric power.
Owen Walcher
http://www.articlesbase.com/home-and-family-articles/installing-a-new-dishwasher-without-a-plumber-81270.html
Technorati Tags: Adjustable Wrench, Attachments, Clamp, Dishwasher Installation, Drain Hose, Electrical Service, Flange, Install Dishwasher, Installing A New Dishwasher, Installing Dishwasher, Needle Nose Pliers, Panel Switch, Plumber, Process Tools, Terminal Screws, Water Inlet, Water Supply Line, Wire Nuts
Posted in electric blanket | No Comments »